Author: Neal

Jason came over for a visit today and reviewed my work on the aft fuse. We talked about some of the wiring runs and some of the more challenging rivets. His comment in the write up of “very high quality” was really encouraging. We also looked over the QB wings and fuse and he gave me some great advice while also pointing out some issues. There is a lack of deburring on the wing spar “waffles”, which I emailed Vans about. Also a couple of scratches and notches that I’ll need to debur.

Later in the day, I went to work riveting a few rivets that I had found to be difficult on the aft fuse, and had left until after I had talked to Jason. These rivets were instructed by the j-channel, and when I set them using the foot of my I long bar, the rivets had a tendency to cleave over. Jason offered a couple of simple suggestions, including taping my other bucking bar to increase mass and center the rivet along the center of mass. This worked great!

Unfortunately I ended up cracking dimples on two rivets, when I stupidly set the rivet while it was not completely square with the holes. For some reason, a alignment issue caused the rivets to not sit squarely in the hole, and instead of investigating and perhaps reeming the hole, I set the rivet. This caused the rivet to transfer stress to the bulkhead flange and crack the edge of the dimple. Really stupidly, I did it twice, on different bulkheads. I didn’t detect the first one until after setting the second rivet. I emailed Vans asking for advice, and went to bed feeling frustrated.

There are a few holes on the aft deck components that need to be match drilled, as they are fabricated by the builder. Today I clecoed and clamped together these parts and drilled the 5 holes.

Today I primed the aft deck components and some of the top skin reinforcing parts. I used 50 grams of part A, and it was just enough to get a coating I was happy with.

Tonight I spent an hour deburring some of the remaining parts for the aft fuselage. Not much to go now, just some aft deck components, and top skin parts with associated stiffeners.

Tonight I riveted on the two aft angle stiffeners, one on each side, below the inspection cover. This was easy, except for the bottom most rivet on each side. No matter what I tried, I struggled to get a bucking bar on the rivet. It worked out ok on one side, and was a mess on the other. Unfortunately, access to the bottom most rivet is almost impossible, so I have not attempted to replace it, for fear of making the situation worse. I’ll review it with my tech counselor when he comes (hopefully soon).

Inside view of right hand stiffener

Today I completed a couple of steps on the aft fuse by attaching the rudder stops and about 30 nut plates.

The rudder stops turned out to be easier than I thought. I was able to start by squeezing the aft two rivets easily, and then bucking the forward two without much trouble. I did the right aft side, then the left aft side, then right forward side, then left. Both came out fine.

Then I dimpled a set of nutplates and started riveting them on. I dimpled 4 nut plates that I shouldn’t have, as I found an error in the drawings. The diagram called out for 9 dimpled nutplates and 5 un-dimpled on each side. But it should have been 7 dimpled and 7 in-dimpled, as there are 7 that sit flush with the longerons. I have a ton of these things, so it didn’t matter at this stage.

I started with all the un-dimpled nutplates, which was quick and easy. Unfortunately I had to drill out a rivet when I inserted it without checking that it was passing through the nutplate. It wasn’t, so I drilled and redid that one.

When I moved onto the dimpled nutplates, I realized I hadn’t held the nutplates steady enough when dimpling. As a result, many of them were slightly bow shaped. This was problematic, as they wouldn’t sit flush against the holes, and had a tendency to break when the second rivet was set. It took me a few nutplates to realize what was going on, and then I drilled out several, dimpled new nutplates (this time holding them level when dimpling), and then re-riveted them on.

The end result was ok. Some of my rivets didn’t set as well as I wanted, but these are not structural, and plenty strong enough to support the screws they will be holding. my main concern was making sure they were straight, aligned with the hole, and not likely to snap off.